Over the weekend, taking an opportunity to check on the final coat of paint, I spent some time and removed most of the masking, leaving only the tape still covering the various varnished bits around the boat.  I forgot to take pictures at this stage, but did take some video footage (which will be available soon).

Now, having missed the morning after events conspired to keep me out of the shop for a while, forcing a change in my intended work plans for the day, I decided the opportunity was ripe to spend the afternoon working on the dinghy.

I started by removing some of the masking tape from the rowlocks, the aft seat support, and one set of the rowing foot braces on the port side, but then decided my time would be better spent preparing the boat for nonskid; I could finish removing the tape any old time I had some spare minutes going forward.  So I changed my focus and, over the next couple hours, masked over the fresh white paint to prepare the field for nonskid.  I sanded away any spills or blotches of white paint from the field as needed.

For the foredeck hatch, I masked a 1″ border along the outer edge, following the shape of the hatch, then sanded the white paint in the field to prepare it for nonskid.

After final cleanup and preparations, I applied the first of two coats of gray nonskid paint to all areas, leaving it to cure overnight.

After final preparations, I applied the third coat of gloss white polyurethane to the interior of the boat, stern and bow, along with another coat on the two smaller pieces–hatch cover and daggerboard trunk filler.  Again, I applied the paint with a brush, working from inside the aft half and outside the forward half.  I was pleased with how this coat turned out and hoped that it would be the final finish inside the boat.

I’d been anxious to get to the third coat of gloss white on the hull interior, but with an aggressive sanding project underway in the next bay taking all my time and making the environment hostile to final paint coats anyway, it took several days before I could finally get back and lightly sand the previous coat of paint.  Afterwards, I cleaned up the boat and shop as needed to prepare for the final coat of paint next time.

The first coat of gloss paint had not been ready to sand the morning after application, but now, the next day, I could–and did–lightly sand the paint with 320 grit paper, scuffing the gloss and correcting a run here or drip there.  Once the sanding was complete, I completely changed up how I’d set up the two halves for painting, as I’d had a continuing challenge with getting reasonable access to the inside of the aft hull, in particular, which was a complicated little thing to paint.

Now, I moved the aft half to the floor, where I set it up on a blanket for protection and added chocks to support it securely, and set up the forward half on the work table.  The forward half, being much smaller and lighter and with a simpler paint scheme, was far less of a problem for access and decent paint application and would work on the raised table, as it hadn’t given me any particular problems with access, but now I planned to literally get in the aft half to allow better access to the complicated after regions, and also allow me to work forward on both sides at once to maintain a wet edge.

Later in the day, after final tack-off and preparations, I applied the second coat of gloss white polyurethane to the inside hull areas.  I’d found previously that many of the spaces were too tight to properly use a roller, so this time I worked with brush alone, and with the better access to the inside of the boat, from being inside myself, I was much more pleased with the results.

After final preparations, I applied the first of at least two coats of gloss white polyurethane to the applicable areas of each hull, along with the foredeck hatch and daggerboard cover.

Over the past couple days I’d finished up the varnish on the tiller and extension (6 coats total), and applied a couple coats of varnish to the epoxy-coated rudder case for protection as well.  These parts were now ready for final assembly whenever the time was right.

Satisfied with the state of the hull interior after priming and sanding, I thoroughly cleaned the surfaces and then laid out for the eventual nonskid pattern to prepare for the final gloss topcoats on the remaining areas.  I started with the aft hull, and laid out a 1″ wide border inboard of the second chine, and around the foot cleats, bulkhead, aft seats, and other areas.  Everything outboard of the masking would receive 2-3 coats of gloss white topcoat.  I cut rounded corners where applicable.

The outside face of the main bulkhead would eventually be painted to match the hull, so I masked it off at the upper corners and all the way around the aft edge of the gunwales.  At the transom, where the inwale met  the transom face itself, I masked a line about 1/4″ down from the radius, which would be the visible dividing line between hull and interior paint.

The forward hull was more straightforward, with 1″ borders along the outboard edges of the foredeck, and around the deck hatch and aft end as well.  As with the aft half, I also masked the face of the mating bulkhead.

Now the hulls were ready for gloss topcoats.

I applied the 4th coat of varnish to the tiller and tiller extension, continuing the daily buildup.

The coatings on both hull halves had had ample cure time, and I spent part of the afternoon sanding to prepare the surfaces for topcoats and final painting.  The primer on the aft hull half sanded easily and well, leaving a silky and consistent surface that would be ready for topcoats after final preparations.  Although the coating was thin in some areas, the primer had done its job and would be an excellent substrate for the gloss topcoats and nonskid that would finish off the aft hull.

The forward hull half, which had mistakenly received a coat of white topcoat rather than primer, turned out well despite the error.  I sanded the finish just as I had on the aft hull, with 220 grit paper on a small sanding block and by hand in the corners and tight areas, and the net result was a well-prepared surface ready for additional coats of topcoat as needed.

Next in the order of things I planned to inspect all areas for any places that might need some fine-tuning (sanding or minor fill work), and then mask off future nonskid areas to prepare for the final gloss topcoats on the remaining surfaces of both hulls.

Using the correct product (primer) this time, I painted the inside of the aft hull section.  The paint was quick to flash off once applied, which led to many lap marks as I struggled to work my way logically through the whole section, which process was admittedly more of a challenge than I’d expected (and I’d expected a challenge).  However, I got coverage everywhere, which was the goal, and since the boat would be sanded before any further work, the lap marks didn’t matter at this stage and frankly couldn’t be avoided despite all efforts.

I painted the face of the forward bulkhead, and also the transom, since these areas would be primed later anyway, and it made sense to do them now.

Meanwhile, I continued the daily buildup of varnish on the tiller, the byproduct of my other project.

I continued the varnish buildup on the tiller and extension with coat #2, an offshoot of my varnish work on another project.

In the afternoon, I saw a good opportunity to apply primer to the interiors of the boat halves.  For this job, I chose Epifanes 2-part polyurethane and appropriate primer for both inside the hull (white) and the outside of the hull (a custom mix to match the owner’s sailboat).  While I’d used, and liked, other Epifanes coatings over the years, I’d not ever used the 2-part specifically.

Earlier in the day, I’d pulled a package containing the paint for the job from a storage area where I’d been keeping it warm, and after confirming the label through the packaging (because I’d ordered both primer and topcoat), pulled out one of the two cans of primer inside the plastic wrapping and set it aside to use now.

I mixed the paint as required and set to work on the forward half, which was the “easier” of the two parts.  For primer, I figured I could cut in and tip with foam brushes, since at the moment I didn’t have any good brushes on hand other than the ones I used for one-part paints, but I didn’t want to start with a used brush.  Immediately, I was surprised at the nature of the primer and, since I chose to start with cutting in the difficult parts of the boat–the underside of the breasthook, and the corners at the aft end beneath the bulkhead gussets and such–I was quickly lamenting the lack of a good brush, but the product was covering fairly well (not as easily as I’d expected), and eventually I coated the whole section satisfactorily.  I was thinking the primer was surprisingly glossy and more finicky to work with than I expected, but overall the coating came out pretty well, and after all, it was just primer.  The small rectangular piece shown is the daggerboard slot cover.

I’d started with a fairly small batch, and while it had been more than enough for the forward half, I could see I’d need more for the second half.  Somewhere around here–I don’t know how exactly  it came into my conscious, it just did all of a sudden–I got a bad feeling, and felt the pangs of Captain Obvious, sometimes abbreviated as “DUH”; I rushed to check my paint can.

Did you see it coming?  It turned out that I’d mixed and used the topcoat for “primer” instead of the primer.  It seems I’d ordered one can of each (I ordered it a while back), and both cans, which looked similar enough to be roughly identical at a glance, had been wrapped in the same overwrap for shipping.  While I’d confirmed the primer label earlier in the day, the can I actually took out was the topcoat.  I was focused on the back of the can, where the mixing instructions were printed, and, being new to the paint, it never was obvious during mixing that I was using the gloss topcoat, especially when I knew I’d read the label through the packaging earlier in the day.  The cans happen to be identical except for the specific product labeling, which one might have thought was enough, but for the specific circumstances and a certain level of brain-deadness.

Doth I protest too much?  Maybe, because I’m embarrassed, but it was also easy to do even in hindsight, particularly when I thought I’d ordered two cans of primer which, naturally, would be packaged together.  Sigh.

Quick:  Which is which?

There’s no shame in mistakes, only in pretending they don’t ever happen.  I share this because it happened, and I could have easily chosen not to share it.

At this point, I cut my losses and left the aft half for another day.   This was a stupid, but not unrecoverable, error, and I planned to treat the first coat of gloss on the forward half just as I would if it was primer.  The good news in all this was that I learned some valuable things about the topcoat application, which would serve me well when I started to actually use the product intentionally later on.

If I’d had enough of the first mix left to complete the aft half, I might have just gone ahead with it despite the error, but since I didn’t have enough already mixed, I saw no reason to push forward.  That said, it’s notable that the designers of the boat write in the manual that “they don’t believe in primer” and the instructions don’t call for priming the boat before painting, even though I chose to stick with my own process and experiences and intended to use primer all along, and which I still think is the correct practice for any coating.

I might have mixed primer and done the aft half correctly, but the primer mix required a mix ratio based on weight, not volume (how annoying, by the way), and I had no means of weighing it at the moment.  It seemed better in all ways to stop and regroup, and turn to the aft half on another day.

No hours were harmed during the making of this mistake.

 

While my main focus remained now on another project at the shop, I still worked on the dinghy most days to continue various epoxy and related steps that were close to being, but not yet, done.

On Monday, I applied a second coat of epoxy to the rudder case, after sanding lightly the first coat, and with the same batch of epoxy applied another coat inside the holes bored for the rowlocks.

On Tuesday, I continued the process on the rudder case, with a third and final coat of epoxy on all sides.

I unmasked the rowlocks, now that the epoxy work was complete there.

At the aft seat, I bunged the screw holes from installation, installing the bungs in thickened epoxy to ensure that the screw holes were filled and watertight, since the installation screws had necessarily penetrated the aft buoyancy tanks.

With this work complete, on Wednesday I could get to some of the final preparations required for primer, mainly cleanup and masking.  I pared away the excess bungs from the aft seat cleats (sorry, forgot to photograph this), and, after cleaning the inside of the boat thoroughly, masked over the various new installations on the aft hull:  aft cleats, foot cleats, and rowlock risers, along with the connecting hardware.  On the forward hull, I masked the connecting hardware and the inside of the mast tube.

Since I had varnish underway for another project at the shop, it was a good opportunity to start the process on the tiller and tiller extension.

To give me better access to the inside of the hulls for painting, I dismantled the 4×8 plywood build table I’d constructed atop one of my normal shop benches, as this work table addition had increased the height by 4″ and made things awkward for reaching inside.  With the boat essentially complete, I no longer had need for the big table, and with it dismantled, I could set one half on the now-lower-and-narrower table, and the other half on a pair of sawhorses of similar height.  Now I was ready for primer whenever I had a time window.